Xbox One loading Blank TV screen or monitor when turned on

Many a time it could so occur that your TV screen or monitor linked along with your Xbox goes clean both when you flip on the console or simply swiftly. It could occur after an replace or after watching a film or simply swiftly for no purpose. In this information, we’ll discuss the right way to repair a clean TV screen or monitor whereas your Xbox One is turned on.

Xbox One loading Blank TV screen or monitor

Before we go forward, be certain that to test all of your connections are in place. All wires are linked correctly, and switches are turned on. Sometimes even the smallest issues are the reason for a much bigger drawback.

Screen goes clean when you’re again to residence or dashboard:

If your TV or monitor screen goes clean everytime you come to your Xbox Dashboard, you must energy cycle your Xbox One. Many a time the ability state of Xbox will get misconfigured, and a easy restart won’t resolve the issue. To recycle energy state comply with the steps under:

  1. Press the Xbox button on your console, and maintain it pressed till you hear a click on, after which your Xbox turns off.
  2. Wait for a minute, after which flip your console on by urgent the Xbox Button. You may also use the Xbox One controller to show it on.
  3. Check if this resolution was useful. Launch an app, after which swap again to the house screen.

Screen goes clean after you begin watching a Blu-ray Disc

The refresh charge (measured in Hz) for displays i.e. how typically a TV modifications the picture or body on the screen is totally different for various media. While Xbox One adapts routinely for a unique sort of media, for motion pictures you want 24Hz refresh charge. This refresh charge is the pure body charge for film viewing. Xbox One enables you to manually change video output. You can set it to permit 24Hz.

  1. Open the Xbox information on your console by urgent the Xbox button.
  2. Then navigate to the rightmost part utilizing the best bumper.
  3. Select System > Settings > Display & sound > Video Output > Video modes 
  4. Select Enable 24Hz.

xbox one loading blank tv screen or monitor when turned on - Xbox One loading Blank TV screen or monitor when turned on

To see if it labored, play a film on the Blu-ray Disc, and see if resolved the issue.

TV or Monitor screen stays clean after you flip on the console:

If the screen stays clean, however you possibly can hear all of the sound popping out from it, after you had turned on your console, the issue is both with the HDMI cable or the decision. It is feasible that current wire configuration was incorrect, and the TV shouldn’t be receiving any enter.

The very first thing to is to test if the HDMI wire is ready up appropriately. Make certain that the wire is ready for TV-out port, and never TV in. If doable, attempt a unique cable with the console, and see if this cable works anyplace else. Also, carry out a energy cycle which I had defined within the above part. If this doesn’t assist, you will want to reset show settings of your console.

The solely possibility left for resolve that is to Reset Screen Resolution of Xbox One. We should boot into decrease decision after which troubleshoot from there.

Note: Make certain to take away any disc within the console earlier than following the steps under.

  • Press and maintain the console button for 5 seconds to show off the console.
  • Now press the and maintain the Xbox button and the Eject button collectively till you hear a beep. This can even flip on the console. Keep holding until you hear the second beep after 10 seconds. You ought to see energy mild flash just earlier than the second beep.xbox one loading blank tv screen or monitor when turned on - Xbox One loading Blank TV screen or monitor when turned on
  • This will boot the console in lowe decision i.e. 640 X 480. Now let’s reset this setting.
  • Go to System > Settings > Display and Sounds > Video possibility > TV decision.
  • Post this, flip off the console, and switch it on once more.

The screen is clean when utilizing Xbox One with AVR

If you’re utilizing an audio-video receiver or AVR, and also you run into this situation, the issue is with connection setup. As the AVR is in between your console and TV, be certain that the cables are in proper ports. We can even should test on the Video output settings on the Xbox as properly.

  1. Connect your set-top field HDMI output to the Xbox One HDMI enter.
  2. Next, join the Xbox One HDMI output to your A/V HDMI enter.
  3. Lastly, join your A/V HDMI output to the HDMI enter on your TV.

Follow the steps under to arrange the best setting for Xbox:

  • Press the Xbox button  to open the information > System Settings > Display & sound > Video output.
  • Select TV connection, after which choose HDMI possibility

If none of those work, its time to attach with the Xbox workforce. They should restore it or change it relying on the problem.

Leave a Comment